Tool Rental Blog

Do-it-yourself Cornhole Match for Tailgates or Yard Entertaining


 

This Do-it-yourself cornhole activity is absolutely sure to be a strike at tailgates and backyard cookouts. Jennifer Largesse of Build Standard designed this Do-it-yourself cornhole board– or bag toss game– to have fold-down legs to make storing and transporting it simple.

All you will need is some venture panel, common components and some very simple resources. Customize it with your favorite group colors or a great layout.

DIY Cornhole Game

Whether or not you connect with it cornhole, baggo, or bag toss, it’s all entertaining with this activity. The critical is to build the very simple frame with fold-down legs, and then customize it with your favorite colors or group emblem. After full, you will have enjoyment for all ages at a cookout, tailgate, or even a massive occasion!  

 

Instruments 

  • Tape Evaluate 
  • Miter Noticed 
  • Jig Noticed 
  • Drill 
  • Drill/Driver 
  • ¾-inch spade bit to build the holes for the rope 
  • 3/8-inch drill bit to build holes for the carriage bolts 
  • 3/16-inch drill bit (or similar) to build the pilot holes 
  • Countersink Drill Little bit 
  • Hammer 
  • Compass  
  • Sander 

Supplies 

Reduce List 

  • 2 x 4 Sides – 4 @ 48 inches 
  • 2 x 4 Finishes – 4 @ 21 inches 
  • 2 x 4 Legs – 4 @ 14½ inches 
  • ½-inch Plywood – 2 @ 24 x forty eight inches 

Actions 

Action one: Reduce the Sections 

Working with a miter noticed, lower the 2 x 4 frame sections to dimensions to build four 48-inch-extensive sides and four 21-inch-extensive finishes. In addition, lower four legs to 14½-inches. 


 Action 2: Make Holes for the Carriage Bolts 

Mark the site of the hole for just about every carriage bolt that will connect the legs 3½-inches from one close of just about every extensive 2 x 4 “side” board. Mark the centre of the line across the width of the board. Location the board on a scrap block.

Working with a drill equipped with a 3/8-inch drill bit, drill by means of the board.

Repeat to prep the remaining sides.  


Action 3: Prep the Frame for Assembly 

Working with a drill equipped with a 3/16 inch drill bit (or similar), drill pilot holes in the vicinity of just about every corner of the extensive “side” boards.  

 


Action 4: Drill the Handle Holes  

Every tackle needs two holes for the rope to fit by means of. Mark the site of these holes on two “side” boards centered on the duration of each board, and spaced 5-inches apart.

Location the 1st board on a scrap piece of wooden. Working with a drill equipped with a ¾-inch spade bit, drill by means of the board at just about every mark.

Repeat to build the holes in the next board.

Observe that one “side” board with handles really should be utilized per assembled game board.  


 

Action five: Angle the Foundation of Every Leg 

Make a mark on the edge of just about every leg that is 1-seven/8 inches from its base. Attract a line from the mark to the opposite corner to build an angled line on one end of just about every leg. Set the miter noticed to about 37-degrees, and then lower the line on just about every leg.  


 

Action 6: Spherical over the Leading of Every Leg 

The top rated of just about every leg requires to be “rounded” to convert freely when hooked up to the frame. The can be carried out by scribing a semicircle on the top rated of the leg and cutting it with a jigsaw, or simply just “clipping” the top rated corners with a miter noticed. To clip the corners, established the miter noticed to forty five-degrees, and then eliminate one inch from just about every corner.  

 


Action seven: Drill a Gap in Every Leg 

Mark a line 1 inch from the top rated edge of just about every leg. Location the 1st leg on a scrap block. Using a drill equipped with a 3/8-inch bit, drill a hole by means of the leg, centered on the line.  

 


Action 8: Mark a Gap on the Plywood 

Make a mark on each plywood project panel that is nine inches from the top rated edge, and centered on the panel.

Set the distribute of a compass to a radius of 3 inches. Rotate the compass about the mark to draw a circle.

Repeat on the next panel.  

 


Action nine: Reduce the Gap 

Location the 1st panel on quite a few scrap blocks to elevate it off the get the job done surface. Set the jigsaw on the edge of the board to make certain that, in its least expensive posture, the blade of the jigsaw runs apparent of the get the job done surface.

Working with a drill equipped with a 3/8-inch drill bit, build a starter hole for the jigsaw inside the marked circle, in the vicinity of its edge.

Location the jigsaw blade into the starter hole, and then cut the perimeter of the circle.

Repeat to build the hole in the remaining panel.  


 

Action ten: Sand the Sections 

Sand the sections smooth getting rid of all splinters and rough edges.  


 

Action 11: Lay Out the Frame 

Location a venture panel face-down on the get the job done surface to use as a information. Location two extensive sides of the frame onto the panel. Sandwich the two limited close boards involving the sides flush with their finishes.   


 

Action 12: Assemble the Frame 

Implement wooden glue to the spots the place the 2 x 4 frame pieces meet.

Then, utilizing a drill/driver, travel 3½-inch exterior-grade wooden screws by means of the pilot holes in the corners of the “sides” and into the limited 2 x 4 close boards.  


 

Action 13: Connect the Deck 

Flip the frame assembly and deck over, then drill pilot holes at just about every corner of the deck. Room them evenly—about each 6 inches—through the deck and into the frame around the perimeter.

Use a countersink bit to prep just about every hole.

Implement wooden glue to the top rated edge of the frame, and then sink 1¼-inch wooden screws by means of the deck and into the frame. Repeat to assemble the remaining activity board.  


 

Action fourteen: Include the Legs 

Generate a carriage bolt through the 3/8-inch holes in just about every frame. Slide a leg onto just about every bolt with the extensive level of its angled base dealing with upward.  

 


Action 15: Set the Bolt 

To established the bolt and preserve it from spinning, strike the bolt with a hammer. Knock the bolt into the wooden till the head of the bolt sets flush versus the wooden and the squared portion down below the head is fully locked into the wooden.  


 

Action 16: Secure the Legs 

Thread a washer and wing nut onto just about every bolt to protected the legs in position.  

 


Action 17: Include the Handles 

Reduce the a few-foot portion of rope in half. Tie a knot at one close of just about every rope.

Feed a piece of rope from the inside of just about every frame to the outside, and then again in by means of the next hole.

Alter just about every tackle till it bows about 2½ inches away from the frame, and then knot the remaining facet inside just about every frame.  

 


Action eighteen: Paint or Stain Your Cornhole Match

Paint your Do-it-yourself cornhole activity to customize it.

And that is it! Delight in your Do-it-yourself cornhole activity.

Locate a lot more Do-it-yourself assignments below on The Home Depot Blog site.

If generating a Do-it-yourself ladder golf activity just is not your issue, we have ladder golf activity devices on the internet in our Garden and Yard Video games portion.

The article Do-it-yourself Cornhole Match for Tailgates or Yard Entertaining appeared 1st on The Home Depot Blog site.



Resource hyperlink